View STPIC6D595_9105825.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

november 2009 doc id 13663 rev 3 1/21 21 STPIC6D595 power logic 8-bit shift register features low r ds(on) : 4 typ eight 100 ma dmos outputs 250 ma current limit capability devices are cascadable low power consumption footprint compatible with stpic6c595 description this STPIC6D595 is a monolithic, medium- voltage, low current power 8-bit shift register designed for use in systems that require relatively moderate load power such as leds. the device contains an 8-bit serial-in, parallel-out shift register that feeds an 8-bit d-type storage register. data transfers through both the shift and storage register clock (srck) and the register clock (rck ), respectively. the device transfers data out the serial output (ser out) port on the rising edge of srck. the storage register transfers data to the output buffer when shift register clear (clr) is high. when clr is low, the input shift register is cleared. when output enable (g ) is held high, all data in the output buffer is held low and all drain output are off. when g is held low, data from the storage register is transparent to the output buffer. when data in the output buffers is low, the dmos transistor outputs are off. when data is high, the dmos transistor outputs have sink-current capability. the ser out allows for cascading of the data from the shift register to additional devices. output are low-side, open-drain dmos transistors with output ratings of 20 v and 120 ma continuous sink-current capability. each output provides a 250 ma maximum current limit at t c = 25 c. the current limit decreases as the junction temperature increases for additional device protection. the device also provides up to 2.0 kv of esd protection when tested using the human-body model. the STPIC6D595 is characterized for operation over the operating case temperature range of -40 c to 125 c. so-16 tssop16 dip-16 table 1. device summary order codes package packaging STPIC6D595mtr so-16 (tape and reel) 2500 parts per reel STPIC6D595ttr tssop16 (tape and reel) 2500 parts per reel STPIC6D595b1r dip-16 25 parts per tube www.st.com
contents STPIC6D595 2/21 doc id 13663 rev 3 contents 1 logic symbol and pin conf iguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.2 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.3 recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.1 dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3.2 switching characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 typical operating circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 typical performance and characteris tics . . . . . . . . . . . . . . . . . . . . . . . 13 7 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 8 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
STPIC6D595 logic symbol and pin configuration doc id 13663 rev 3 3/21 1 logic symbol and pin configuration figure 1. pin configuration figure 2. logic symbol
maximum rating STPIC6D595 4/21 doc id 13663 rev 3 2 maximum rating stressing the device above the rating listed in the ?absolute maximum ratings? table may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not imp lied. exposure to absolute ma ximum rating conditions for extended periods may affect device reliability. 2.1 absolute maximum ratings 2.2 thermal data table 2. absolute maximum ratings symbol parameter value unit v cc logic supply voltage (see note 1 )7v v i logic input voltage range -0.3 to 7 v v ds power dmos drain to source voltage (see note 2 )20v i d pulsed drain current, ea ch output, all output on (t c = 25 c) 250 ma i d continuous current, each output, all output on (t c = 25 c) 100 ma i d peak drain current single output (t c = 25 c) (see note 3 ) 250 ma p d continuous total dissipation (t c 25 c) 1087 mw p d continuous total dissipation (t c = 125 c) 217 mw t j operating virtual junction temperature range -40 to +150 c t c operating case temperature range -40 to +125 c t stg storage temperature range -65 to +150 c t l lead temperature 1.6 mm (1/16 inch) from case for 10 seconds 260 c table 3. thermal data symbol parameter package values unit r th(ja) thermal resistance junction-ambient dip-16 85 c/w so-16 107 tssop16 143
STPIC6D595 maximum rating doc id 13663 rev 3 5/21 2.3 recommended operating conditions table 4. recommended operating conditions symbol parameter min max unit v cc logic supply voltage 4.5 5.5 v v ih high level input voltage 0.85v cc v cc v v il low level input voltage 0 0.15v cc v i dp pulse drain output current (t c = 25 c, v cc = 5 v, all outputs on) (see note 3 , note 4 ) 250 ma t su set-up time, ser in high before srck (see figure 4 and figure 8 ) 10 ns t h hold time, ser in high after srck (see figure 4 , figure 7 , figure 8 ) 10 ns t w pulse duration (see figure 8 )40ns t c operating case temperature -40 125 c
electrical characteristics STPIC6D595 6/21 doc id 13663 rev 3 3 electrical characteristics 3.1 dc characteristics v cc = 5 v, t c = 25 c, unless otherwise specified. table 5. dc characteristics symbol parameter test conditions min typ max unit v (br)dsx drain-to-source breakdown voltage i d = 1 ma 20 v v sd source-to-drain diode forward voltage i f = 100 ma 0.85 1.2 v v oh high level output voltage ser out i oh = -20 a v cc = 4.5 v 4.4 4.49 v i oh = -4 ma v cc = 4.5 v 4 v v ol low level output voltage ser out i oh = 20 a v cc = 4.5 v 1 100 mv i oh = 4 ma v cc = 4.5 v 145 300 mv i ih high level input current v cc = 5.5 v v i = v cc 1 100 na i il low level input current v cc = 5.5 v v i = 0 -1 -100 na i cc logic supply current v cc = 5.5 v all outputs off or on 23 40 a i cc(frq) logic supply current at frequency f srck = 5 mhz c l = 30 pf all outputs off (see figure 6 , (1) ) 1. not tested, specified by design 70 250 a i n nominal current v ds(on) = 0.5 vi n = i d t c = 85 c (see note 4 , note 5 , note 6 ) (1) 120 200 ma i dsx off-state drain current v ds = 20 v v cc = 5.5 v or 0 v 0.02 1 a v ds = 20 v v cc = 5.5 v or 0 v t c = 125 c 0.5 1 a r ds(on) static drain source on state resistance (see note 4 , and note 5 ) i d = 50 ma v cc = 4.5 v 3.4 4 i d = 50 ma v cc = 4.5 v t c = 125 c 4.8 6 i d = 100 ma v cc = 4.5 v 3.5 6
STPIC6D595 electrical characteristics doc id 13663 rev 3 7/21 3.2 switching characteristics v cc = 5 v, t c = 25 c, unless otherwise specified. note: 1 all voltage value are with respect to gnd 2 each power dmos source is internally connected to gnd 3 pulse duration 100 s and duty cycle 2% 4 technique should limit t j - t c to 10 c maximum 5 these parameters are measured with voltage sensing contacts separate from the current- carrying contacts. 6 nominal current is defined for a consistent comparison between devices from different sources. it is the current that produces a voltage drop of 0.5 v at t c = 85 c. table 6. switching characteristics symbol parameter test conditions min typ max unit t phl propagation delay time, high to low level output from g c l = 30 pf i d = 75 ma (see figure 4 , figure 5 , figure 6 , figure 7 ,) -1930ns t plh propagation delay time, low to high level output from g -4670ns t phl-sdo propagation delay time, clock to sdo -1925ns t plh-sdo propagation delay time, clock to sdo -4660ns t plh-r_o propagation delay low to high level rck to out -6290ns t phl-r_o propagation delay high to low level rck to out -1318ns t plh-s_so propagation delay low to high level sck to sdo -1420ns t phl-s_so propagation delay high to low level sck to sdo -1420ns t r rise time, drain output - 20 30 ns t f fall time, drain output - 15 20 ns
logic diagram STPIC6D595 8/21 doc id 13663 rev 3 4 logic diagram figure 3. logic diagram
STPIC6D595 typical operating circuit doc id 13663 rev 3 9/21 5 typical operating circuit figure 4. typical operation mode test circuits figure 5. typical operation mode waveforms note: 1 a) the word generator has the following characteristics: t r 10 ns, t f 10 ns, t w = 300 ns, pulse repetition rate (prr) = 5 khz, z o = 50 2b) c l includes probe and jig capacitance.
typical operating circuit STPIC6D595 10/21 doc id 13663 rev 3 figure 6. typical operation mode test circuits figure 7. switching time waveform
STPIC6D595 typical operating circuit doc id 13663 rev 3 11/21 figure 8. input setup and hold waveform note: 1 a) the word generator has the following characteristics: t r 10 ns, t f 10 ns, t w = 300 ns, pulse repetition rate (prr) = 5 khz, z o = 50 2b) c l includes probe and jig capacitance. t w t h t su t phl- s do / t plh - s do s rck
typical operating circuit STPIC6D595 12/21 doc id 13663 rev 3 figure 9. input equivalent circuit figure 10. output equivalent circuit
STPIC6D595 typical performance and characteristics doc id 13663 rev 3 13/21 6 typical performance and characteristics unless otherwise specified t j = 25 c figure 11. static drain-source on-state resistance vs logic supply voltage figure 12. supply current vs frequency figure 13. supply current vs supply voltage figure 14. switching time vs case temperature 2 2.5 3 3.5 4 4.5 5 4.5 5 5.5 6 6.5 7 r dson ( ) vcc (v) t a = 125 c t a = 85 c t a = 25 c t a = -40 c 0 200 400 600 800 1000 0.1 1 10 100 1000 icc (ua) f (mhz) 0 0.02 0.04 0.06 0.08 0.1 4.5 5 5.5 6 icc (ma) vcc (v) tplh tphl tr tf 10 20 30 40 50 4.50 4.70 4.90 5.10 5.30 5.50 t(ns) vcc
package mechanical data STPIC6D595 14/21 doc id 13663 rev 3 7 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark.
STPIC6D595 package mechanical data doc id 13663 rev 3 15/21 dim. mm. inch min. typ max. min. typ. max. a1 0.51 0.020 b 0.77 1.65 0.030 0.065 b 0.5 0.020 b1 0.25 0.010 d 20 0.787 e 8.5 0.335 e 2.54 0.100 e3 17.78 0.700 f 7.1 0.280 i 5.1 0.201 l 3.3 0.130 z 1.27 0.050 plastic dip-16 (0.25) mechanical data p001c
package mechanical data STPIC6D595 16/21 doc id 13663 rev 3 dim. mm. inch min. typ max. min. typ. max. a 1.75 0.068 a1 0.1 0.25 0.004 0.010 a2 1.64 0.063 b 0.35 0.46 0.013 0.018 b1 0.19 0.25 0.007 0.010 c 0.5 0.019 c1 45 (typ.) d 9.8 10 0.385 0.393 e 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 8.89 0.350 f 3.8 4.0 0.149 0.157 g 4.6 5.3 0.181 0.208 l 0.5 1.27 0.019 0.050 m 0.62 0.024 s8 (max.) so-16 mechanical data 0016020d
STPIC6D595 package mechanical data doc id 13663 rev 3 17/21 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.2 0.504 0.519 d 20.2 0.795 n 60 2.362 t 22.4 0.882 ao 6.45 6.65 0.254 0.262 bo 10.3 10.5 0.406 0.414 ko 2.1 2.3 0.082 0.090 po 3.9 4.1 0.153 0.161 p 7.9 8.1 0.311 0.319 tape & reel so-16 mechanical data
package mechanical data STPIC6D595 18/21 doc id 13663 rev 3 dim. mm. inch min. typ max. min. typ. max. a 1.2 0.047 a1 0.05 0.15 0.002 0.004 0.006 a2 0.8 1 1.05 0.031 0.039 0.041 b 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0079 d 4.9 5 5.1 0.193 0.197 0.201 e 6.2 6.4 6.6 0.244 0.252 0.260 e1 4.3 4.4 4.48 0.169 0.173 0.176 e 0.65 bsc 0.0256 bsc k0? 8?0? 8? l 0.45 0.60 0.75 0.018 0.024 0.030 tssop16 mechanical data c e b a2 a e1 d 1 pin 1 identification a1 l k e 0080338d
STPIC6D595 package mechanical data doc id 13663 rev 3 19/21 dim. mm. inch min. typ max. min. typ. max. a 330 12.992 c 12.8 13.2 0.504 0.519 d 20.2 0.795 n 60 2.362 t 22.4 0.882 ao 6.7 6.9 0.264 0.272 bo 5.3 5.5 0.209 0.217 ko 1.6 1.8 0.063 0.071 po 3.9 4.1 0.153 0.161 p 7.9 8.1 0.311 0.319 tape & reel tssop16 mechanical data
revision history STPIC6D595 20/21 doc id 13663 rev 3 8 revision history table 7. document revision history date revision changes 20-jun-2007 1 first release 06-sep-2007 2 change from preliminary to final version 17-nov-2009 3 updated: ta b l e 2 , ta b l e 3 , ta b l e 5 , ta bl e 6 , ta bl e 6 , figure 1 , figure 7 , figure 8 and figure 9 added: figure 2 , figure 11 , figure 12 , figure 13 and figure 14
STPIC6D595 doc id 13663 rev 3 21/21 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorized st representative, st products are not recommended, authorized or warranted for use in milita ry, air craft, space, life saving, or life sustaining applications, nor in products or systems where failure or malfunction may result in personal injury, death, or severe property or environmental damage. st products which are not specified as "automotive grade" may only be used in automotive applications at user?s own risk. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2009 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of STPIC6D595

	To Download STPIC6D595 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .